AP Racing Catalogue Issue 4

74 visit www.apracing.com for installation drawings & up to date product range details CP2293-162, CP2293-163 & CP2293-176 - 340cc CAPACITY TYPES ◘ Three 340cc capacity plastic reservoirs, with either offset or central outlets, which screw directly into all master cylinders with 7/16” UNF inlet thread, or can be used remotely. ◘ Volume = 340cm³ (20.7in³) ◘ Supplied with CP2293-173 rubber diaphragm (Bellows) to minimise entry of mois- ture and dirt, and help prevent spillage. ◘ Supplied complete with cap 3847-246 & adaptor. ◘ “Push on” inlet version available. Part No CP2293-176 . CP2293-69 & 4342-372 TYPES ◘ A large capacity remote plastic reservoir with 1 outlet. ◘ CP2293-69 supplied with diaphragm (bellows) CP2293-174 & cap 3847-246. ◘ 4342-372 supplied without diaphragm (bellows) & cap 4325-148. ◘ Accepts Ø5/16” diameter hose. ◘ Volume = 280cm³ (17.1in³). CP2293-85 & 4342-355 TYPES ◘ A large capacity remote plastic reservoir with 2 outlets. ◘ CP2293-85 supplied with diaphragm (bellows) CP2293-174 & Cap 3847-246. ◘ 4342-355 supplied without diaphragm (bellows) & cap 4325-148. ◘ Accepts Ø5/16” diameter hose. ◘ Volume = 280cm³ (17.1in³) CP2293-141 / CP2293-143 & CP4623-7 / CP4623-8 TYPES ◘ A large capacity plastic reservoir with offset outlet, which screws directly into themaster cylinders detailed below. ◘ Can be supplied with or without rubber diaphragm (bellows), CP2293-174. ◘ Supplied complete with cap 4325-148, or alternative cap 3847-246 if bellows are fitted, and adaptor. ◘ CP2293-141 & -143 suitable for: CP2623, CP4400 & CP6093. ◘ CP4623-7 & -8 suitable for: CP4623 & CP5623. ◘ To rotate reservoir, unlock nut included and reposition, then re-tighten. Part No. Diaphragm Fitting CP2293-141 No 7/16” UNF CP2293-143 Yes CP4623-7 Yes M12x1.0 CP4623-8 No Volume 275cm³ (13.4in³). DIAPHRAGMS (BELLOWS) Rubber Diaphragms (bellows) minimise the entry of moisture and dirt to help prevent spillage. The diaphragms listed below are suitable for use with appropriate AP Racing reservoirs in this catalogue. NOTE: The use of Diaphragms (bellows) may restrict effective volume of reservoirs. CP2709-156 (SMALL) ◘ For use with reservoir cap LBNM9057AXBR, on the follow- ing reservoir assemblies. All CP4709 Series except -12, -13, -16 & -19. CP2293-174 (MEDIUM) ◘ For use with reservoir cap 3847-246, on the following reservoir assemblies. CP2293-141, -143 & -69 / CP2293-85 / 4342-355 / CP4623-7/-8 /-9 & -10. Replaces CP2293-48. CP2293-173 (LARGE) ◘ For use with reservoir cap 3847-246, on the following reservoir assemblies - CP2293-162 /-163 /-176 & -185. Replaces CP2293-166. IMPORTANT NOTE: When fitting new bellows CP2293-173 (supercedes CP2293-166) & CP2293-174 (supercedes CP2293-48), to old 4325-148 cap assembly, the plastic insert and rubber seal must be removed from the cap.New cap 3847-246. OD = Ø72mm (2.83") Ø89 (3.50") 115 (4.53") 12 (0.47") Ø88.50 Ø72.80 145.30 7/16" UNF 19.50 22.00 21.25 CP2293-162 7/16" UNF Ø72.80 Ø88.50 145.30 22.00 19.50 CP2293-163 FLUID RESERVOIRS Note: Drawing for guidance only. Download latest issue installation drawing from www.apracing.com 89.25 MAX 25.40 51.10 / 50.50 7.15 6.85 Ø 36.20 35.80 Ø88.50 MAX Ø72.90 MAX 3.35 MAX 101.00 MAX 15.00 MIN SPACE TO REMOVE CAP 27.50 MAX Ø7.95/7.65 Ø9.70/9.30 79.00 MAX Ø89 (3.50") 102 (4.00") 25 (1.00") 18 (0.70") 90 (3.55") 50 (2.00") Ø6.5 (0.25") Ø73 (2.85") 20 (0.80") 20 (0.80") CP2293-178 & CP2293-185, 400cc CAPACITY TYPES ◘ Two 400cc capacity plastic reservoirs, with either a central or offset outlet, supplied with 3/8”UNF push on adaptor fitting. ◘ Volume = 400cm³ (24.4in³) ◘ Supplied without bellows, but optional bellows fitment available: IMPORTANT NOTE: CP2293-178 & -185 can be fitted with CP2293-173 bellows if required. However, the plastic insert and rubber seal must be removed, otherwise the bellow, will not fit correctly. ◘ Supplied complete with cap 4325-148 and CP2623-250 adaptor. 143.50 25.40 A/F CP2293-178 CP2293-178 CP2293-185 10.40 9.90 7.35 6.85 Ø SUPPLIED WITH A PUSH ON FITTING 22.0 CAP Ø88.5 IF USING CP2293-176 BELLOWS, PLASTIC INSERT AND SEAL MUST BE REMOVED TIGHTEN LOCK NUT TO 7Nm 20.90 8.70 9.00 Ø72.8 154.00 MAX